WALL PANELS

Ordering Tips

Half panel roman blind, lined or unlined (RB5)

A similar style to our full panel roman blind (RB4) but the intermediate (base edge of each stack) is a soft fold without a seam. Hence this style has less horizontal seams than the RB4 style blind. When the blind is fully stacked horizontal seams can not be seen.
Like the RB4 style, this blind is ideal for wider width windows if you’d like to avoid vertical fabric joins.

• Suitable Fabrics:
  This is the most suitable structured roman blind style, when using sheer or lightweight fabrics and a lined blind is required. This style can also be used with solid fabrics.
  Select a preferably plain fabric, where horizontal seams will not interrupt the fabric pattern. For wide width windows, select a wide width fabric that can be railroaded to avoid vertical seams from fabric joins. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  This blind style is usually made lined but can be unlined on request. Our standard lined RB5 blind includes 3 pass blockout stiffened lining in ivory colour. Other lining options available include: 3 pass stiffened white lining, 3 pass non-stiffened white or ivory lining, 1 pass off white or ivory lining, translucent polyester neutral lining.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Stack ups and batten spacing will be calculated based on total drop of blind and customer styling requirements specified to BQ. Front stacks range from 27.5cm to 33.5cm.

Full panel roman blind, lined or unlined (RB4)

A modern blind style with horizontal seams sewn in face fabric at all folds and visible at the intermediate (base edge of each stack) when the blind is raised. This style provides you with a soft roman if using sheer or lightweight fabrics without lining. Alternatively use this style with solid fabrics and stiffened 3 pass lining to create a firmer structured roman with horizontal seams.
This blind style is ideal for wider width windows if you’d like to avoid vertical fabric joins.
For an unlined RB4 blind, battens are sewn into back pockets of the main fabric at the base and top of each stack, giving the blind more structure than our other soft roman blind style RB6. Side edges of blinds can be sewn on request, if prefer to avoid tape.
For a lined RB4 blind, battens are sewn into the lining at the base and top of each stack.

• Suitable Fabrics:
  Suitable for solid, sheer or lightweight fabrics. Select a preferably plain fabric, where horizontal seams will not interrupt the fabric pattern. For wide width windows, select a wide width fabric or fabric that can be railroaded to avoid vertical seams from fabric joins. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  If adding lining to the RB4 style blind, our standard lining is 3 pass blockout stiffened lining in ivory colour. Other lining options available include: 3 pass stiffened white lining, 3 pass non-stiffened white or ivory lining, 1 pass off white or ivory lining, translucent polyester neutral lining.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Stack ups and batten spacing will be calculated based on total drop of blind and customer styling requirements specified to BQ. Front stacks range from 27.5cm to 33.5cm.

Standard roman blind, lined (RB1)

A structured contemporary and popular blind style. The blind appears flat when down with no visible sewn seams except for wide width blinds that may require vertical fabric joins. Sits in a neat folded stack when blind is raised.

• Suitable Fabrics:
  Solid plain or pattern fabrics you want to showcase. For wider width blinds, print fabric will be expertly pattern matched where vertical fabric joins are required. For butting windows installed on the same window or bay windows, fabric pattern flow can be provided on request. Additional fabric metreage may be required. Velvets are not suitable for main fabric or bands. For light coloured sheers a RB4 style with sewn sides or a RB5 style is recommended. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  This blind style is always lined. Lining is built into the structure of the blind and battens are sewn into back pockets in the lining. Our standard blind includes 3 pass blockout stiffened ivory lining. Other lining options available include: 3 pass stiffened white lining, 3 pass non-stiffened white or ivory lining, 1 pass off white or ivory lining, translucent polyester neutral lining.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Stack ups and batten spacing will be calculated based on total drop of blind and customer styling requirements specified to BQ. Front stacks range from 27.5cm to 33.5cm.

Front batten roman blind, lined (RB2)

A classic lined blind style with thin battens stitched into horizontal fabric pockets seen on the front side of the blind. The fabric pockets sit at the intermediate (base edge of each stack) when the blind is stacked.

• Suitable Fabrics:
  Solid plain or pattern fabrics where horizontal joins wont interrupt the pattern. Works well with vertical stripe fabrics. Avoid horizontal stripes. For wider width blinds, print fabric will be expertly pattern matched where vertical fabric joins are required. For butting windows installed on the same window or bay windows, fabric pattern flow can be provided on request. Additional fabric metreage may be required.

Velvets are not suitable for main fabric or band. For light coloured sheers a RB4 style with sewn sides or a RB5 style is recommended. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  This blind style is always lined. Lining is built into the structure of the blind and battens are sewn into back pockets in the lining. Our standard blind includes 3 pass blockout stiffened ivory lining. Other lining options available include: 3 pass stiffened white lining, 3 pass non-stiffened white or ivory lining, 1 pass off white or ivory lining, translucent polyester neutral lining.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Stack ups and batten spacing will be calculated based on total drop of blind and customer styling requirements specified to BQ. Front stacks range from 27.5cm to 33.5cm.

Ordering Tips

Flanged (BH10)

A flanged slip cover is pulled tightly over an upholstered bedhead frame. A 1cm flange sits on top and side edges. Flange size can vary on request.

Skirting board and base cut-out not available.

Bedhead shapes available: 9 only.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics. We can also quilt your fabric prior to upholstering for added interest. The bedhead flange will also be quilted.
  View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single sized flanged bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead. The wall mounting bracket (2cm projection) is attached to the slip cover, hence cover can not be removed. Wall mounting bracket can be omitted on request.
  • Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to plasterwork. Bedhead will sit slightly above floor, as base cut-outs unavailable with this bedhead style.

  The Flanged style bedhead sits up to 2cm away from wall if wall mounted above skirting boards or bedhead sits on floor between bed and wall. Skirting board cutout is unavailable.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 4cm (excludes wall mounting bracket).

Ordering Tips

Evo

Evo curtains offers a similar look to Inverted Pleat curtains, although they are made with a single pleat at the back which enables the curtain to stack back efficiently to maximise the window vantage.

Evo curtains runs on a glide system and require an Evo rod. BQ supply two styles of glides suitable for Evo rods or supply your own glides.

BQ uses 90mm wide clear buckram for an Evo curtain heading.

• Suitable Fabrics:
  Solid fabrics.

• Lining:
  Select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Evo curtains can also be made unlined when using a solid fabric.

• Seams:
  Vertical fabric join seams will be hidden on curtain heading.

• BQ standard fullness:
  x2.5 for solid fabrics. Other fullness options available on request. Evo curtains require more fabric to Inverted Pleat curtains.

• Maximum Drop:
  600cm

Ordering Tips

Inverted Pleat

Inverted Pleat curtains are also known as a reverse pleat or box pleat and offers a contemporary look. This curtain style does not stack back as comprehensively as other styles. Evo curtains offer a similar heading style with a more condensed stack back.

BQ uses 100mm wide buckram for the curtain heading.

• Suitable Fabrics:
  Solid and sheer fabric types, although heading buckram will be obvious on very sheer unlined fabrics. For fabrics with vertical stripes, consider the interuption to pattern flow along the curtain heading due to pleats. For fabrics with vertical stripes, consider the interruption to pattern flow along the curtain heading due to inverted pleats.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• Seams:
  Vertical fabric join seams will be hidden on curtain heading.

• Hooks:
  When ordering, specify your preferred two prong hook size depending on the type of rod or track to be used and the curtain position required. Visit Customer Login for further hook info.

• BQ standard fullness:
  x1.8 for solid and sheer fabrics. Other fullness options available on request.

• Maximum Drop:
  600cm

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Scandi

An unstructured minimalist heading style with soft loose folds.

Similar to a Flat Panel curtain but made with a discreet 100mm wide heading without the stiff buckram heading tape.

• Suitable Fabrics:
  Solid and sheer fabrics with a soft handle for the best result in hanging. Contact BQ to confirm fabric suitability. This heading style is not suitable for very fine or thin sheers, very open weave sheers or heavy stretchy fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• Maximum Drop:
  600cm

• Hooks:
  Scandi curtains are supplied with pin hooks placed 5mm from curtain top edge and 100mm apart as standard, or request alternate positioning to suit type of rod or track used.

• BQ standard fullness:
  x1.8 for solid and sheer fabrics. Other fullness options available on request. Request less fullness for a curtain with minimal folds or for a curtain with fuller looser folds and more body and fabric request greater fullness and consider wider hook spacing.

Relaxed Fold

A relaxed and modern heading style with gentle irregular folds.  The curtain is made with a flat finish heading with no pleating or gathering.

BQ uses a soft 75mm wide white heading tape, with clear tape available on request.

• Suitable Fabrics:
  Solid and sheer fabrics with a soft handle for the best result in hanging.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested.

• BQ standard fullness:
  x2 for solid and sheer fabrics. Other fullness options available. Request less fullness for a curtain with minimal folds or for a curtain with fuller looser folds and more body and fabric greater fullness.

• Maximum Drop:
  600cm

Flat Panel

Flat Panel curtains offer a simple and versatile curtain style. The curtain is made with a flat finish heading with no pleating or gathering. When the curtain is hung on a rod or track, curtains with a standard 1.5 fullness will sit in gentle waves. For an almost flat curtain with minimal or no wave when closed, request a low curtain fullness or for a curtain heading style with fuller loose waves request a higher curtain fullness.

Flat panel curtains are often used with a decorative rod with or without rings.

BQ uses a 100mm wide buckram for the curtain heading, creating a stiffer heading style than Scandi curtains.

• Suitable Fabrics:
  Solid and sheer light to medium weight fabrics including linens, cottons and silks. Heading buckram will be obvious on very sheer unlined fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested.

• BQ standard fullness:
  x1.5 for solid fabrics. Other fullness options available on request.

• Maximum Drop:
  600cm

Ripplefold (S-fold)

Ripplefold curtains are a contemporary and popular curtain style with neat and simple uniform folds. The curtains are made with a 30mm wide press stud heading tape provided by our customer.

They are installed with a ripplefold track or rod installed above the window or on the ceiling.

• Suitable Fabrics:
  Solid and sheer fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• Maximum Drop:
  600cm

• BQ standard fullness:
  x2.2 for solid and sheer fabrics. Other fullness options available on request.

Ordering Tips

Headrail system

Bonded Roller Blind – Ordering Tips

FABRIC

QUANTITY & SIZING

This bedhead style consists of a 15cm wide padded band and square panel sewn insert with blind button detail.

Additional rows of panels are available on request, for non standard height bedheads.

A calico insert sits behind mattress.

Bedhead shapes available: 8 and 9.

Chain Side: Chain not required for blinds with a motorisation system or spring assist.

Fabric: Please provide the following fabric information to BQ if applicable (and upload images to assist) :

* Face side of fabric and pattern direction, if confusion may occur
* Contrast fabric/trim exact placement and sizing

* if using the fabric(s) mentioned with another BQ order.

Fabric pattern match : Please notify BQ if you have fabric pattern match requirement. Additional fabric may be required. If multiple blinds are installed in the same room, BQ will pattern match print fabric from base of blind as standard and the pattern will be centred and horizontally aligned on each blind.

Fabric pattern flow : Please notify BQ if you have fabric pattern flow requirement where print fabric is used on adjoining/butting blinds. Additional fabric may be required.

How Measure Width:

• Pin to Pin : The finished width of blind from bracket to bracket, including roller. For face fix blinds provide your architrave to architrave width.For blinds installed in recess, provide recess width and select Recessed – YES and we will make adjustments for perfect blind fit in recess.
• Cloth to Cloth : The finished width of the blind fabric only.
  

Mounting:
The following options are available for securing your bedhead:

• Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
• All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
• Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to the wall. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

The Square Panel Insert style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is requested.

Railroaded Fabric : Railroaded fabric is suitable for wide width fabrics and standard width fabrics where blind drop is 1100mm or less.

Recessed: Please specify if blind will be installed in a window recess. BQ will make adjustments to  your measurements to ensure perfect fit.

Roll:

Normal roll: Fabric falls to back of roller (BQ standard).

Reverse roll: Fabric falls to front of roller, covering roller tube.

Window Name: Please provide location of window to assist with queries, package labeling and installation.

Eyelet

Eyelet curtains are made with individual metal eyelet rings punched through the fabric. Eyelet sizes come in a 60mm external diameter and 40mm internal diameter. The 40mm internal diameter best suits a 25mm curtain rod.

BQ supply a nickel plated (silver) steel eyelet as our standard or zinc, brass, antique brass or black eyelets can be used on request.

• Suitable Fabrics:
  Solid and sheer fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• BQ standard fullness:
  x2 for solid fabrics and x2.5 for sheer fabrics. Other fullness options available on request.

• Maximum Drop:
  600cm

Soft gather roman blind
(RB6 unlined, RB7 lined)

An unstructured roman blind style that gathers from the base when raised. No battens are added.

Blinds are made with a vertical stitching line in middle and both sides of blind, in colour matched thread at position of blind cords on back side. Wide width blinds may have multiple evenly spaced vertical stitching lines where cords are positioned.

• Suitable Fabrics:
  The RB6 unlined roman blind style is recommended for sheer or lightweight fabrics and is made without lining.
  The RB7 lined roman blind style is recommended for solid fabrics and is made with lining. Fabric suitability should be discussed with BQ before proceeding. For wider width blinds, print fabric will be expertly pattern matched where vertical fabric joins are required. For butting windows installed on the same window or bay windows, fabric pattern flow can be provided on request. Additional fabric metreage may be required. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  If adding lining to your soft roman, our standard lining for the RB7 style blind is translucent polyester lining in a neutral colour. Other lining options available include: 3 pass non-stiffened white or ivory lining and 1 pass off white or ivory lining.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop.

Shape 1

Channel

Ideal for: bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads.

BQ offer the following channel quilting methods:

• Multi-needle channel quilting
• Frame channel quilting
• Outline channel quilting

The recommended quilting method depends on the size of the finished product, width and fabric (plain or patterned) used and required channel direction. All our channel quilting methods have the same filling and lining options mentioned below. 

Multi-needle channel quilting

Multi-needle quilting is our most common channel quilting method and our most affordable quilting style.

Straight evenly spaced lines are quilted on the length direction of the fabric, to create channels.

• Quilting dimensions:
  The following channel widths are available: 7.5cm, 10cm, 12.5cm, 15cm, 17.5cm, 20cm or 22.5cm. Consider the finished size of your quilted product when deciding channel width. Use for reversible product styles only when fabric joins not required eg: throw rugs. Quilting dimensions are approximates and vary depending on filling weight used.

• Process used:
  The fabric is quilted first in panels approximately 150cm wide and of unlimited length. We then cut, join panels and sew your fabric according to the style and size of your selected product. This ensures fabric joins are concealed in the stitched channel. When joining pattern fabric on wide width products such as bedspreads and quilt covers, perfect pattern match can not always be achieved.

• Suitable fabrics:
  Plain or patterned fabric in standard or wide width where the pattern can be easily joined and pattern matched. Durable medium to heavy weight fabrics preferred. For patterned fabrics with wide pattern repeats or those that can not be easily patterned matched we may suggest channel frame quilting. For patterned fabrics with a horizontal or linear pattern, we suggest outline channel quilting if channels are to perfectly align with the fabric pattern.

• Thread:
  Black or natural colour

Frame channel quilting

Channels can be sewn in a vertical or horizontal direction. Recommended for products using a coloured quilting thread rather than black or natural and for bedspreads and quilt covers using patterned fabric that is not easily pattern matched.

Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  The following channel widths are available: 15cm, 20cm, 25cm and 30cm. Consider the finished size of your quilted product when deciding channel width. Quilting dimensions are approximates and vary depending on filling weight used.

• Process used:
  First we cut and join the fabric and then we quilt, providing pattern and quilting match. Fabric joins will be exposed especially on plain fabrics.

• Suitable fabrics:
  Plain and patterned fabrics. Durable medium to heavy weight fabrics preferred. Wide width fabrics are recommended on larger products such as bedspreads and quilt covers, to avoid visible fabric joins. If channel quilting a patterned fabric and fabric joins are required, frame channel quilting may provide better pattern match than multi-needle channel quilting, although fabric joins are likely to be visible rather than hidden in channels as is possible with multi-needle channel quilting . For fabrics with a horizontal or linear pattern, we suggest outline channel quilting if channels are to perfectly align with the fabric pattern.

• Thread:
  Colour matched to suit the main background colour of your fabric.

Outline channel quilting

A straight line of stitching traces along the check or stripe pattern of the fabric, emphasising the fabric pattern and providing greater stitching accuracy as compared to other quilting methods. Recommended for king size bedspreads that may be too large for frame quilting.

• Quilting dimensions:
  Channel width is dependent on the fabric design.

• Process used:
  We cut and join the fabric first and then we quilt, providing pattern and quilting match. Outline quilting is completed by hand by our experienced machinists.

• Suitable fabrics:
  Patterned fabrics with a straight horizontal or linear pattern, and where quilting lines need to exactly follow the fabric pattern to form a quilted channel look. Durable medium to heavy weight fabrics preferred.

• Thread:
  Colour matched to suit the main background colour of your fabric.

Bonded Pelmet

An unpadded pelmet, available in a straight, shape 1 and 3 only.
Made with 4.5mm piping along top and base edge of pelmet, in self or contrast fabric. Piping can be omitted on request.
Fabric is bonded to a strong wood custom made pelmet frame.
Combine with curtains, roman blinds or roller blinds.

• Suitable fabrics:
  Most medium and heavy weight solid fabrics are suitable for pelmets, although linen and viscose blends may stretch over time. Light weight fabrics such as silks and sheers can be used but cotton interlining is recommended and can be supplied by BQ.
  Fabrics can be railroaded on request to avoid joins or consider wide width fabrics to minimise amount of fabric required. If using a patterned fabric, railroading may not be suitable. BQ will expertly pattern match at fabric joins.

• Sizing:
  Provide width, drop and return measurements for either inside box measurements (IBM) or outside box measurements (OBM). Cut-outs can be added to ensure pelmet fits perfectly. Maximum drop is 40cm and maximum size of returns is 20cm. For pelmets over 390cm customer must organise own freight or collection from BQ’s Melbourne workroom. Alternatively, pelmets can be made in two or three pieces. We recommend three pieces to avoid a centre join and interruption to any fabric pattern.

Goblet Pleat

Goblet pleat curtains provide a formal style. If you are furnishing a traditional or stately old home and have a sumptuous fabric a Goblet style heading could be a good option.

BQ use 100mm wide clear buckram for the curtain heading and each goblet is filled with wadding.

• Suitable Fabrics:
  Solid fabrics.

• Lining:
  Select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Goblet pleat curtains can also be made unlined when using a solid fabric.

• Seams:
  Vertical fabric join seams will be hidden on curtain.

• Hooks:
  When ordering, specify your preferred two prong hook size depending on the type of rod or track to be used and the curtain position required. Visit Customer Login for further hook info.

• BQ standard fullness:
  x2 for solid. Other fullness options available on request.

• Maximum Drop:
  600cm

Gather Pleat

Shaped base

Double fold at top

Double fold at top with contrast band

Dropped base

Piping

Add 4.5mm or 7mm piping if not already part of our standard bedhead style. Select like or contrast fabrics, added to bedhead sides where seams exist or back edge where bedhead sits along wall.

Suitable for bedhead styles: BH1, BH2, BH3 and BH13.

We can also add braid or decorative cord trim to replace piping on face of BH3 and BH4 bedhead styles.

Shape 9

5 Panel (BH15)

Five separate panels with plain fronts and no side seams.

Bedhead shapes available: 9 only.

Suitable Fabrics:
Best for plain fabrics, vinyls, leathers and suede.
We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.

Sizing:
Select a standard size detailed below or request a customised size. Single, king single and double size bedheads not available. Maximum height 170cm.

Queen: 270 cm W x 120cm H
King: 320 cm W x 120cm H

Finished bedhead projection (from centre of bedhead) is 5.5cm.

Mounting:
The following options are available for securing your bedhead:

• Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall. Plates to join the panels and small metal legs are available on request to be fastened onsite.
• Each panel is supplied with a wall mounting bracket to enable bedhead attachment to the wall, providing greater stability. Walls must be strong enough to hold approx 50kg of bedhead.
• Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to plasterwork. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

The 5 Panel bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

Semicircle (BH14)

Semicircle shaped bedhead with plain front and no side seams.

Bedhead shapes available: 10 only.

Suitable Fabrics:

Sizing:
Select a standard size detailed below or request a customised size. Non standard sizes not available.

Single: 110cm W x 120cm H
King Single: 127cm W x 129cm H
Double: 158cm W x 144cm H
Queen: 173cm W x 152cm H
King: 203cm W x 167cm H

Finished bedhead projection (in centre of bedhead) is 7cm.

Mounting:
The following options are available for securing your bedhead:

• Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
• All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
• Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to plasterwork. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

The Semicircle style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

Deep Diamond Button (BH7)

Upholstered with covered deeply inset buttons in a diamond configuration. Optional surrounding wings in shapes A-E can be added. Studs or sewn wall can be added to wing.

Bedhead shapes available: 1, 4, 8 and 9.

Base cut-out not available.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  Fabric must be railroaded.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede.
  Contrast fabrics can also be used on bedhead buttons.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall. Recommended if wings added.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
  • Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to wall. Bedhead will sit slightly above floor, as base cut-outs unavailable with this bedhead style.

  The Deep Diamond Button style bedhead sits flushed to the wall if mounted above skirting boards or bedhead sits on floor and a skirting board cut-out is included. If optional wings added, skirting board cut-out also added to wings. Base cut-out unavailable.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	120cm W x 120cm H
  King Single:	120cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 10.5cm.

Vertical Panel (BH6)

Consists of vertical deep panels approx. 20cm each in width. Panels can be made wider on request.

Bedhead shapes available: 8 and 9.

Base cut-out not available.

• Suitable Fabrics:
  Best for plain fabrics, vinyls, leathers and suede.
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
  • Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to plasterwork. Bedhead will sit slightly above floor, as base cut-outs unavailable with this bedhead style.

  The Vertical Panel style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 10.5cm.

Walled (BH5)

Plain style front with 5cm seamed walled side and 4.5mm piping on front and back wall edge. Piping can be omitted on request.

Bedhead shapes available: 1 to 8, and 9 if no piping required.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest. View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on piping and side wall.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 9cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
  • Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to plasterwork. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

  The Walled style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

Plain (BH4)

A plain style front with no side seams and single row of 7mm piping on back wall edge. Piping can be omitted on request.

Bedhead shapes available: 1 to 8, and 9 if no piping required.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest.View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on piping.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 6cm. Add a further 2cm to projection if a wall mounting bracket is attached.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
  • Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to plasterwork. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

  The plain style bedhead sits 2cm away from wall if mounted above skirting boards or sits on floor. Skirting board cut-out is unavailable.

Padded Roll (BH3)

Consists of a padded roll with 7mm piping inserted below roll. Roll width is 9cm for single bed and 12.5cm all other bed sizes. 60cm high main insert sits deeper than surrounding roll. Calico insert sits behind mattress (can be omitted on request, additional main fabric may be required).

Bedhead shapes available: 1 to 8

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. For added interest, we can also quilt fabric for the main insert, prior to upholstering. View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on bedhead roll, insert and piping.
  Please note: calico fabric is upholstered behind mattress with this bedhead style. If you require calico to be omitted, please mention on BQ Order Form and supply sufficient fabric as quoted by BQ.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 6cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall. There will be a gap between the bedhead and wall depending on width of skirting board.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
  • Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to plasterwork. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

  The padded roll style bedhead sits up to 2cm away from wall if mounted above skirting boards or sits on floor. Skirting board cutout is unavailable.

Padded Band (BH2)

Consists of a 15cm wide padded band with 7mm piping inserted below band and 60cm high main insert. 5cm seamed walled side. Calico insert sits behind mattress.

Bedhead shapes available: 8 and 9

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. For added interest, we can also quilt fabric for the main insert, prior to upholstering.View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on bedhead band, insert, piping and side wall.
  Please note: calico fabric is upholstered behind mattress with this bedhead style. If you require calico to be omitted, please mention on BQ Order Form and supply sufficient fabric as quoted by BQ.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 7cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
  • Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to plasterwork. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

  The Padded Band style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

Stuckey (BH1)

A plain short style with foam padding in 5.5cm or 10cm (BQ standard) projection. Sits neatly along the mattress, flushed to the wall. Does not go to floor.

Bedhead shapes available: 9 only

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest. View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on covered buttons or piping on back wall edge, if requested.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width is 210cm. This bedhead style is made 5cm wider than the standard mattress width.

  Single:	97cm W x 60cm H
  King Single:	112cm W x 60cm H
  Double:	143cm W x 60cm H
  Queen:	158cm W x 60cm H
  King:	188cm W x 60cm H

• Mounting:
  Bedhead needs to be attached to wall, using wall mounting bracket provided by BQ.

Duo (BH12)

Two separate panels with plain fronts and 50mm seamed walled sides.

Bedhead shapes available: 8 (slightly rounded corners) is standard. Shape 9 (square corners) available on request.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest.
  View our quilting styles.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection (at centre of bedhead) is 9cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall. Plates to join the panels and small metal legs are available on request to be fastened onsite.
  • Both panels are supplied with a wall mounting bracket to enable bedhead attachment to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
  • Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to wall. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

  The Duo style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is requested.

Square Panel Insert (BH13)

This bedhead style consists of a 15cm wide padded band and square panel sewn insert with blind button detail.

Additional rows of panels are available on request, for non standard height bedheads.

A calico insert sits behind mattress.

Bedhead shapes available: 8 and 9.

Sizing:
Select a standard size detailed below or request a customised size. Single size bedhead not available. Maximum width 210cm and maximum height 170cm.

King single : 127cm W x 120cm H
Double: 158cm W X 120cm H
Queen: 173cm W X 120cm H
King: 203cm W X 120cm H

Finished bedhead projection (from centre of bedhead) is 8cm.

Mounting:
The following options are available for securing your bedhead:

• Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
• All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
• Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to the wall. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

The Square Panel Insert style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is requested.

Suitable Fabrics:
Best for plain fabrics, vinyls, leathers and suede.
We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.

Quilted with bound edge (BT2)

The throw rug face side is quilted in a multi-needle channel, frame or outline style and finished with a bound edge, in same or contrast fabric on all sides.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Quilted with contrast band on four edges (BT8)

The throw rug face side is quilted in a channel, multi-needle or outline style and finished with a 10cm contrast band on all sides, visible on face side only.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Quilted with 4.5mm piped edge (BT3)

The throw rug face side is quilted in a multi-needle channel, frame or outline style and finished with a 4.5mm piped edge, in same or contrast fabric on all sides. 7mm piping also available on request.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Quilted with flange (BT6)

The throw rug face side is quilted in a multi-needle channel, frame or outline style and finished with a 7cm flange edge, in same or contrast fabric on ends only. Other flange sizes can be requested.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Quilted with contrast band on ends (BT7)

The throw rug face side is quilted in a multi-needle channel, frame or outline style and finished with a 15cm contrast band on ends only, visible on face side. Other band sizes can be requested.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Filling Options

Square

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  BQ can quilt 15cm, 20cm, 25cm or 30cm squares. When selecting size of quilted square, consider the finished product size if a full square is to be achieved along the finished product edges. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, patterned fabrics will be pattern matched. Fabric joins can often be more visible and exposed on plain fabrics or fabrics with minimal pattern. Durable medium to heavy weight fabrics preferred.

• Process Used:
  BQ use a frame quilting method to create perfectly quilted squares. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread colours:
  Colour matched to suit the main background colour of your fabric.

Tuft Square

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  Tufts are spaced every 15cm horizontally and 15cm vertically.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Durable medium to heavy weight fabrics preferred. Heavily embroidered fabrics not recommended for tuft quilting.

• Process Used:
  BQ use a frame quilting method to create even tuft spacing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Tuft Diamond

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  Tufts are spaced every 30cm horizontally and 30cm vertically. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Durable medium to heavy weight fabrics preferred. Heavily embroidered fabrics not recommended for tuft quilting.

• Process Used:
  BQ use a quilting frame to create even tuft spacing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Elongated Diamond

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  23cm high x 20cm wide. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins.

• Process Used:
  BQ use a quilting frame to create even tuft spacing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Straight Diamond

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  30cm x 30cm. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Durable medium to heavy weight fabrics preferred.

• Process Used:
  BQ use a quilting frame to create even tuft spacing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Border with Straight Diamond

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  30cm x 30cm. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Durable medium to heavy weight fabrics preferred.

• Process Used:
  BQ use a quilting frame to create even tuft spacing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Outline Channel

A straight line of stitching traces along the check or stripe pattern of the fabric, emphasising the fabric pattern and providing greater stitching accuracy as compared to other quilting methods. Channel width is dependent on the fabric design.

• Quilting Process Used:
  We cut and join the fabric first and then we quilt, providing pattern and quilting match. Outline quilting is completed by hand by our experienced machinists.
  Recommended for king size bedspreads that may be too large for frame quilting.

• Suitable Fabrics:
  Pattern fabrics with a straight horizontal or linear pattern, and where quilting lines need to exactly follow the fabric pattern to form a quilted channel look. Durable medium to heavy weight fabrics preferred.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Outline Pattern

Emphasises the pattern on your floral, plaid or check fabric.
Our machinest traces a line of stitching around the fabric pattern. Recommended for patterns not too busy and not too spread out across fabric.

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads.

• Suitable Fabrics:
  Durable medium to heavy weight fabrics preferred.

• Process Used:
  First we cut and join the fabric and then our machinest sews your unique quilting pattern suited to your fabric.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Lining

Filling Options

Rod Pocket

Rod Pocket curtains are a simple, easy to hang curtain, made with a sewn in pocket at the top of each curtain, to allow a curtain rod to be threaded through.

• Suitable Fabrics:
  Solid and sheer fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• BQ standard fullness:
  x2 for solid fabrics and x2.5 for sheer fabrics. Other fullness options available on request.

• Maximum Drop:
  600cm

Tab Top

Tab Top curtains are made with 50mm wide x 100mm high tab loops evenly spaced and sewn to curtain top. The tab loops are thread onto a curtain rod.

• Suitable Fabrics:
  Solid and sheer fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• BQ standard fullness:
  x1.5 for solid and sheer fabrics. Other fullness options available on request.

• Maximum Drop:
  600cm

Knife Pleat

As an alternative to a gathered heading a Knife Pleat offers a neat and tailored look.

BQ uses 50mm wide gathering tape laid flat.

• Suitable Fabrics:
  Sheer fabrics with no lining attached.

• Hooks:
  When ordering, specify your preferred row to position gathering hook depending on the type of rod or track to be used and the curtain position required.

• Maximum Drop:
  600cm

• BQ standard fullness:
  x3 for sheer fabrics. Other fullness options available on request.

Pencil Pleat

A Pencil Pleat is similar to a gathered curtain in that a heading tape of one or multiple rows can be applied to gather the fabric into pencil style pleats. The main difference is the pencil pleat heading tape is 75mm wide instead of 30mm for gathered curtains, which creates a neater and more stable pleat.

BQ uses white fabric gathering tape with or nylon transparent gathering tape for very sheer fabrics, is available on request.

• Suitable Fabrics:
  Solid and sheer fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• Maximum Drop:
  600cm

• Hooks:
  When ordering, specify your preferred pocket position to place gathering hook (top, middle or bottom row) depending on the type of rod or track to be used and the curtain position required.

• BQ standard fullness:
  x2 for solid and x2.5 for sheer fabrics. Other fullness options available on request.

Pinch Pleat

Wave

Wave curtains are similar to ripplefold curtains although they are made with a wider 80mm heading tape with inbuilt plastic hooks, provided by our customer.

They are installed with a wave curtain track or rod.

• Suitable Fabrics:
  Solid and sheer fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• Maximum Drop:
  600cm

• BQ standard fullness:
  x2.2 for solid and sheer fabrics. Other fullness options available on request.

Scatter cushions

BQ offer the following scatter cushion design options:

• Plain unpiped
• Piped edges, with 4.5mm or 7mm piping in self or contrast fabric
• Flanged edges in self or contrast fabric
• Contrast fabric bands
• Add trim, braid, tassels, fringe, covered buttons or French seam.
• Add quilting

Polyester or feather inserts in standard sizes are available from BQ, or supply your own.

Cushions are made with a concealing flap to hide zip opening. Zip is colour matched to your fabric.

• Suitable Fabrics:
  When selecting a fabric consider usage of cushion, washing instructions, fabric shrinkage, durability, and softness against the skin. Light sheer fabrics are not suitable for cushions unless lined and used for decorative purposes. Outdoor fabrics can be used, however BQ do not use weather resistant zips, thread and foam. If adding contrast fabric piping, flange or reverse side to your cushion design, consider fabric composition and behaviour of the fabric as compared to the main fabric. For plain or flanged cushions with same pattern fabric used on both sides, some side seams can be pattern matched on request. Additional fabric may be required.

• Sizing:
  Select a standard square or rectangle size detailed below or request a customised size. All sizes below exclude flange.

  38 x 38 cm

  40 x 40 cm

  45 x 45 cm

  50 x 50 cm

  55 x 55 cm

  60 x 60 cm

  65 x 65 cm

  30 x 45 cm

Roll direction

A normal roll, with roller sitting to front of blind and fabric falling to back of roller, is our standard configuration. A reverse roll, with roller sitting to back of blind is available on request, however BQ production warranty will not apply.
Alternatively add a pelmet or window valance to hide roller componentry.

Suitable Fabrics

Plain edges

Unpiped plain quilt cover style.

Fabric can be quilted to add further interest to your quilt cover. Face side only is quilted, unless otherwise requested. View our quilting styles.

• Suitable Fabrics:
  Consider washing instructions, fabric creasing, shrinkage, durability, and softness against the skin when selecting a suitable fabric for your quilt cover. Polyesters, polyester/cotton mixes and pre-shrunk cottons wash well and are common fabrics used for bedding. Natural fabrics such as cottons and linens breath well but may shrink over time if not pre-shrunk. Linens are especially popular for a relaxed look. Sheer and velvet fabrics are not suitable for quilt covers.
  If adding contrast fabric to underside of your quilt cover design consider the composition and behaviour of this fabric as compared to the face fabric. Single sized unquilted bedspreads can be made with standard width (140cm) fabrics. For all other quilt cover sizes, wide width fabrics are recommended to avoid fabric joins.Fabrics will be pattern matched at joins on quilt cover face side. Side seams can be pattern matched on request, if fabric pattern allows. Additional fabric may be required.The following fabric options are available for the underside of the quilt cover: same as face fabric, contrast fabric, customer supplied flat sheet or BQ provided ivory cotton lining.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single (unquilted):	136cm W x 210cm L
  Single (quilted):	140cm W x 210cm L
  Double:	180cm W x 210cm L
  Queen:	210cm W x 210cm L
  King:	240cm W x 210cm L
  Super King:	270cm W x 240cm L

Pleated Window Valance

Our standard BQ window valance is made with box pleats evenly spaced across the facade and front corners of the window valance. Pleats are positioned approximately 50cm apart depending on total width of window valance and a 15cm headboard projection is used, unless otherwise specified. Maximum drop is 50cm.

Window valances can also be made with a centre pleat and front corner pleats only or with a plain facade and box pleats in front corners only.

The plain facade style is recommended for smaller windows or windows with a blind and window valance in same print fabric.

• Lining Options:
  • cotton supreme lining, in ivory (BQ standard) or off white colour
  • 1 pass lining, in ivory or off white colour
  • 3 pass blockout lining, in ivory or white colour
  • no lining

• Suitable Fabrics:
  Use solid, non sheer light to medium weight fabrics that will form sharp firm permanent pleats when pressed.

Upholstered Pelmet

A padded pelmet, available in straight or shaped styles.
Made with 4.5mm piping along top and base edge of pelmet, in self or contrast fabric. Piping can be omitted on request although it is recommended for shaped pelmets as gives a neater base finish. Piping can also be replaced with decorative cord.
Combine with curtains, roman blinds or roller blinds.

• Suitable fabrics:
  Most medium and heavy weight solid fabrics are suitable for pelmets, although linen and viscose blends may stretch over time. Light weight fabrics such as silks and sheers can be used but cotton interlining is recommended and can be supplied by BQ. Fabrics can be railroaded on request to avoid joins or consider wide width fabrics to minimise amount of fabric required. If using a patterned fabric, railroading may not be suitable. BQ will expertly pattern match at fabric joins. For piping using striped fabrics, fabric is cut on the bias giving a diagonal stripe effect.

• Bay windows:
  If placing pelmets on a bay window, Straight, and shapes 1, 3, 4 (if centre is made straight) and 5 are available. In each instance the centre window of the bay will have a straight pelmet with shaped pelmets on both outer bay windows. Velcro tabs are supplied for butting pelmets to ensure a neat finish at the joins.

• Sizing:
  Provide width, drop and return measurements for either inside pelmet box (IBM) or outside pelmet box (OBM). Cut-outs can be added to ensure pelmet fits perfectly. Maximum drop is 40cm and maximum size of returns is 20cm. For pelmets over 390cm customer must organise own freight or collection from BQ’s Melbourne workroom. Alternatively, pelmets can be made in two or three pieces. We recommend three pieces to avoid a centre join and interruption to any fabric pattern.

Band with piping above

Suitable for straight upholstered style only.

Band and/or piping may be in contrast or self fabric and piping can be replaced with decorative cord.

Band is approximately 60cm high unless otherwise specified.

Shape 10

Base options

Finish the base of your blind with the following base options:

Floor length bedspread

Sits to the floor or further extend the finished drop of your bedspread to create a puddling effect.

Chain options

Our blinds are chain operated providing smooth, consistent and reliable movement.

Chain colour options available include:

• White plastic (BQ standard)
• Birch white plastic
• Black plastic
• Nickel plated brass (silver in colour)
• Stainless steel – rust resistant and recommended for bathrooms and seaside locations.

The chain is secured to a wall mounted chain tensioner by your installer, to ensure child safety regulations are met.

The blind brackets, chain drive and chain tensioner will be the same colour as the plastic chain or colour matched to the fabric if a nickel or stainless steel chain is used. Clear coloured chain tensioners are also available.

If you prefer a blind without a chain, you can add motorisation to your blind also ideal for hard to reach blinds. Spring operation is also available for some blind styles.