WHO WE WORK WITH

Half panel roman blind, lined (RB5)

A similar style to our full panel roman blind (RB4) but the intermediate (base edge of each stack) is a soft fold without a seam. Hence this style has less horizontal seams than the RB4 style blind. When the blind is fully raised horizontal seams can not be seen.
Like the RB4 style, this blind is ideal for wider width windows if you’d like to avoid vertical fabric joins.

View gallery for more images of our Customised Roman Blind styles.

• Suitable Fabrics:
  This structured roman blind style is suitable for sheer or lightweight fabrics and a lined blind is required. This style can also be used with solid fabrics.
  Select a preferably plain fabric, where horizontal seams will not interrupt the fabric pattern. For wide width windows, select a wide width fabric that can be railroaded to avoid vertical seams from fabric joins. Velvets are not suitable for main fabric or bands. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  Our standard lined RB5 blind includes 3 pass blockout stiffened lining in ivory colour. Other lining options available include: 3 pass stiffened white lining, 3 pass non-stiffened white or ivory lining, 1 pass off white lining or polyester (translucent) lining in neutral colour..

• Contrast bands and trims:
  For blinds with a contrast band or decorative trim added to the blind base or inset from base, when the blind is fully raised the base of the blind will sit below the stack so the contrast band or trim is visible.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Stack ups and batten spacing will be calculated based on total drop of blind and customer styling requirements specified to BQ. Front stacks range from 27.5cm to 33.5cm.

Casual fold roman blind
(RB8 unlined, RB9 lined)

An unstructured roman blind style made without battens that softly folds (rather than gathers as occurs with our soft gather roman blind) when the blind is raised.

When the blind is closed it sits as a flat panel of fabric with no horizontal seams or gathering. Each fold is 150mm deep and the blind is finished with a fabric lathe base, 100mm standard side turns and discreet vertical stitch lines in colour matched thread align with the strings required for blind operation.

View gallery for more images of our Customised Roman Blind styles.

• Suitable Fabrics:
  Recommended for sheer or lightweight fabrics, plain or pattern fabrics. When the blind is raised, linen and other natural fibre fabrics will sit with more softness and drape, compared to fabrics with a high polyester content that will sit with firmer straighter folds. Wide width fabrics are recommended for wider windows to avoid vertical fabric joins. If fabric joins are required, print fabric will be expertly pattern matched. For butting blinds installed on the same window or bay windows, fabric pattern flow can be provided on request. Additional fabric metreage may be required. Velvets are not suitable for main fabric or bands and decorative trims can be added for additional interest. Fabric suitability should be discussed with BQ before proceeding. The casual fold roman blind style requires less fabric than our other unlined blind styles.

• Lining:
  If adding lining to your casual fold roman blind, our standard lining for the RB9 blind is translucent polyester lining in a neutral colour. Other lining types not available.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Finished drop is measured to base lathe.

Soft gather roman blind
(RB6 unlined, RB7 lined)

An unstructured roman blind style that gathers from the base when raised. No battens are added.

When blind is closed three stationery fabric folds sit at base of blind. These folds can be removed or reduced on request. Vertical stitching lines in colour matched thread is present in middle and both sides of blinds. Wide width blinds may have multiple evenly spaced vertical stitching lines where cords sit at back of blind. Blinds have standard 100mm side turns.

View gallery for more images of our Customised Roman Blind styles.

• Suitable Fabrics:
  The RB6 unlined roman blind style is recommended for sheer or lightweight fabrics and is made without lining.
  The RB7 lined roman blind style is recommended for solid fabrics and is made with translucent polyester lining. Fabric suitability should be discussed with BQ before proceeding. For wider width blinds, print fabric will be expertly pattern matched where vertical fabric joins are required. For butting blinds installed on the same window or bay windows, fabric pattern flow can be provided on request. Additional fabric metreage may be required. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  If adding lining to your soft roman, our standard lining for the RB7 style blind is translucent polyester lining in a neutral colour. Other lining types not available.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Finished drop is measured to base fabric fold rather than base lathe.

Base options

Chain options

Our blinds are chain operated providing smooth, consistent and reliable movement.

Chain colour options available include:

• White plastic (BQ standard)
• Birch white plastic
• Black plastic
• Nickel plated brass (silver in colour)
• Stainless steel – rust resistant and recommended for bathrooms and seaside locations.

The chain is secured to a wall mounted chain tensioner by your installer, to ensure child safety regulations are met.

The blind brackets and chain drive will be the same colour as the plastic chain or colour matched to the fabric if a nickel or stainless steel chain is used. A clear chain tensioner will be supplied. For recessed blinds we can also provide white, birch white, or black round shaped tensioners, on request.

If you prefer a blind without a chain, you can add motorisation to your blind also ideal for hard to reach blinds. Spring operation is also available for some blind styles.

Full panel roman blind, lined or unlined (RB4)

A modern blind style with horizontal seams sewn in face fabric at all folds and visible at the intermediate (base edge of each stack) when the blind is raised. This style provides you with a soft roman if using sheer or lightweight fabrics without lining. Alternatively use this style with solid fabrics and stiffened 3 pass lining to create a firmer structured roman with horizontal seams.
This blind style is ideal for wider width windows if you’d like to avoid vertical fabric joins.
For an unlined RB4 blind, battens are sewn into back pockets of the main fabric at the base and top of each stack, giving the blind more structure than our other soft roman blind style RB6. Side edges of blinds can be sewn on request, if prefer to avoid tape.
For a lined RB4 blind, battens are sewn into the lining at the base and top of each stack.

View gallery for more images of our Customised Roman Blind styles.

• Suitable Fabrics:
  Suitable for solid, backcoated, sheer or lightweight fabrics. Select a preferably plain fabric, where horizontal seams will not interrupt the fabric pattern. For wide width windows, select a wide width fabric or fabric that can be railroaded to avoid vertical seams from fabric joins. Velvets are not suitable for main fabric or bands. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  If adding lining to the RB4 style blind, our standard lining is 3 pass blockout stiffened lining in ivory colour. Other lining options available include: 3 pass stiffened white lining, 3 pass non-stiffened white or ivory lining, 1 pass off white lining, translucent polyester neutral lining.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Stack ups and batten spacing will be calculated based on total drop of blind and customer styling requirements specified to BQ. Front stacks range from 27.5cm to 33.5cm. For blinds with a contrast band or decorative trim added to the blind base or inset from base, when the blind is fully raised the base of the blind will sit below the stack so the contrast band or trim is visible.

Front batten roman blind, lined (RB2)

A classic lined blind style with thin battens stitched into horizontal fabric pockets seen on the front side of the blind. The fabric pockets sit at the intermediate (base edge of each stack) when the blind is stacked.

View gallery for more images of our Customised Roman Blind styles.

• Suitable Fabrics:
  Solid plain or pattern fabrics where horizontal joins wont interrupt the pattern. Works well with vertical stripe fabrics. Avoid horizontal stripes. For wider width blinds, print fabric will be expertly pattern matched where vertical fabric joins are required. For butting blinds installed on the same window or bay windows, fabric pattern flow can be provided on request. Additional fabric metreage may be required.

Velvets are not suitable for main fabric or band. For light coloured sheers a RB4 style with sewn sides or a RB5 style is recommended. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  This blind style is always lined. Lining is built into the structure of the blind and battens are sewn into back pockets in the lining. Our standard blind includes 3 pass blockout stiffened ivory lining. Other lining options available include: 3 pass stiffened white lining, 3 pass non-stiffened white or ivory lining, 1 pass off white lining, translucent polyester neutral lining.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Stack ups and batten spacing will be calculated based on total drop of blind and customer styling requirements specified to BQ. Front stacks range from 27.5cm to 33.5cm. For blinds with a contrast band or decorative trim added to the blind base or inset from base, when the blind is fully raised the base of the blind will sit below the stack so the contrast band or trim is visible.

Standard roman blind, lined (RB1)

A structured contemporary and popular blind style. The blind appears flat when down with no visible sewn seams except for wide width blinds that may require vertical fabric joins. Sits in a neat folded stack when blind is raised.

View gallery for more images of our Customised Roman Blind styles.

• Suitable Fabrics:
  Solid plain or pattern fabrics you want to showcase. For wider width blinds, print fabric will be expertly pattern matched where vertical fabric joins are required. For butting blinds installed on the same window or bay windows, fabric pattern flow can be provided on request. Additional fabric metreage may be required. Velvets are not suitable for main fabric or bands. For light coloured sheers a RB4 style with sewn sides or a RB5 style is recommended. Visit Customer Login for further fabric suitability info or contact BQ.

• Lining:
  This blind style is always lined. Lining is built into the structure of the blind and battens are sewn into back pockets in the lining. Our standard blind includes 3 pass blockout stiffened ivory lining. Other lining options available include: 3 pass stiffened white lining, 3 pass non-stiffened white or ivory lining, 1 pass off white lining, translucent polyester neutral lining.

• Sizing:
  Maximum size is 340cm wide x 300cm drop. BQ Design’s production warranty does not apply to blinds greater than 300cm wide x 300cm drop. Stack ups and batten spacing will be calculated based on total drop of blind and customer styling requirements specified to BQ. Front stacks range from 27.5cm to 33.5cm. For blinds with a contrast band or decorative trim added to the blind base or inset from base, when the blind is fully raised the base of the blind will sit below the stack so the contrast band or trim is visible.

Base options

Finish the base of your blind with the following base options:

Base options

Finish the base of your blind with the following base options:

Elongated Diamond

• Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.
  

• Quilting dimensions:
  22cm wide x 38cm high. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Velvets not suitable.

• Process Used:
  BQ use a quilting frame to create perfectly sized diamonds. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric or select a contrast colour thread.

Straight Diamond

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king or larger size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  15cm x 15cm. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Durable medium to heavy weight fabrics preferred. Velvets not suitable.

• Process Used:
  BQ use a quilting frame to create identical diamond sizing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric or select a contrast colour thread.

Tailored seams at foot corners, no pleats (BV6)

• Suitable Fabrics:
  Light, medium and heavy weight non sheer fabrics. Light weight fabrics can be lined.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	92cm W x 188cm L x 33cm D
  King Single:	107cm W x 203cm L x 33cm D
  Double:	138cm W x 191cm L x 33cm D
  Queen:	153cm W x 204cm L x 33cm D
  King:	183cm W x 204cm L x 33cm D

Quilted (BV4), 10cm channel quilting is standard

Alternate channel widths and quilting styles are available. View quilting styles.

• Suitable Fabrics:
  Light, medium and heavy weight non sheer fabrics. Velvets not suitable. Light weight fabrics can be lined. Visit Customer Login for further fabric suitability info or contact BQ.

• Filling:
  Quilted with 100g weight polyester filling as BQ standard. Other filling options available on request include:
  • 70g polyester for a flatter effect
  • 150g polyester for a puffier effect
  • bumph – 100% cotton, for a completely flat look

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	92cm W x 188cm L x 33cm D
  King Single:	107cm W x 203cm L x 33cm D
  Double:	138cm W x 191cm L x 33cm D
  Queen:	153cm W x 204cm L x 33cm D
  King:	183cm W x 204cm L x 33cm D

Inverted pleat at foot corners, centre of sides and centre of foot (BV2)

• Suitable Fabrics:
  Light, medium and heavy weight non sheer fabrics. Some heavy fabrics such as velvets may not fold and pleat firmly. Light weight fabrics can be lined.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	92cm W x 188cm L x 33cm D
  King Single:	107cm W x 203cm L x 33cm D
  Double:	138cm W x 191cm L x 33cm D
  Queen:	153cm W x 204cm L x 33cm D
  King:	183cm W x 204cm L x 33cm D

Sewn down inverted pleat at foot corners only (BV5A)

• Suitable Fabrics:
  Light, medium and heavy weight non sheer fabrics. Light weight fabrics can be lined.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	92cm W x 188cm L x 33cm D
  King Single:	107cm W x 203cm L x 33cm D
  Double:	138cm W x 191cm L x 33cm D
  Queen:	153cm W x 204cm L x 33cm D
  King:	183cm W x 204cm L x 33cm D

Ordering Tips

Ordering Tips

Ordering Tips

Sizing

Ordering Tips

Channel

Ideal for: bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads.

BQ offer the following channel quilting methods:

• Multi-needle channel quilting
• Frame channel quilting
• Outline channel quilting

The recommended quilting method depends on the size of the finished product, width and fabric (plain or patterned) used and required channel direction. All our channel quilting methods have the same filling and lining options mentioned below. 

Multi-needle channel quilting

Multi-needle quilting is our most common channel quilting method and our most affordable quilting style.

Straight evenly spaced lines are quilted on the length direction of the fabric, to create channels.

• Quilting dimensions:
  The following channel widths are available: 7.5cm, 10cm, 12.5cm, 15cm, 17.5cm, 20cm or 22.5cm. Consider the finished size of your quilted product when deciding channel width. Use for reversible product styles only when fabric joins not required eg: throw rugs. Quilting dimensions are approximates and vary depending on filling weight used.

• Process used:
  The fabric is quilted first in panels approximately 150cm wide and of unlimited length. We then cut, join panels and sew your fabric according to the style and size of your selected product. This ensures fabric joins are concealed in the stitched channel. When joining pattern fabric on wide width products such as bedspreads and quilt covers, perfect pattern match can not always be achieved.

• Suitable fabrics:
  Plain or patterned fabric in standard or wide width where the pattern can be easily joined and pattern matched. Durable medium to heavy weight fabrics preferred. For patterned fabrics with wide pattern repeats or those that can not be easily patterned matched we may suggest channel frame quilting. For patterned fabrics with a horizontal or linear pattern, we suggest outline channel quilting if channels are to perfectly align with the fabric pattern. Velvets not suitable.

• Thread:
  Black or natural colour

Frame channel quilting

Channels can be sewn in a vertical or horizontal direction. Recommended for products using a coloured quilting thread rather than black or natural and for bedspreads and quilt covers using patterned fabric that is not easily pattern matched.

Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  The following channel widths are available: 15cm, 20cm, 25cm and 30cm. Consider the finished size of your quilted product when deciding channel width. Quilting dimensions are approximates and vary depending on filling weight used.

• Process used:
  First we cut and join the fabric and then we quilt, providing pattern and quilting match. Fabric joins will be exposed especially on plain fabrics.

• Suitable fabrics:
  Plain and patterned fabrics. Durable medium to heavy weight fabrics preferred. Wide width fabrics are recommended on larger products such as bedspreads and quilt covers, to avoid visible fabric joins. If channel quilting a patterned fabric and fabric joins are required, frame channel quilting may provide better pattern match than multi-needle channel quilting, although fabric joins are likely to be visible rather than hidden in channels as is possible with multi-needle channel quilting . For fabrics with a horizontal or linear pattern, we suggest outline channel quilting if channels are to perfectly align with the fabric pattern.

• Thread:
  Colour matched to suit the main background colour of your fabric.

Outline channel quilting

A straight line of stitching traces along the check or stripe pattern of the fabric, emphasising the fabric pattern and providing greater stitching accuracy as compared to other quilting methods. Recommended for king size bedspreads that may be too large for frame quilting.

• Quilting dimensions:
  Channel width is dependent on the fabric design.

• Process used:
  We cut and join the fabric first and then we quilt, providing pattern and quilting match. Outline quilting is completed by hand by our experienced machinists.

• Suitable fabrics:
  Patterned fabrics with a straight horizontal or linear pattern, and where quilting lines need to exactly follow the fabric pattern to form a quilted channel look. Durable medium to heavy weight fabrics preferred.

• Thread:
  Colour matched to suit the main background colour of your fabric.

Square

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  BQ can quilt 15cm, 20cm, 25cm or 30cm squares. When selecting size of quilted square, consider the finished product size if a full square is to be achieved along the finished product edges. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, patterned fabrics will be pattern matched. Fabric joins can often be more visible and exposed on plain fabrics or fabrics with minimal pattern. Durable medium to heavy weight fabrics preferred. Velvets not suitable.

• Process Used:
  BQ use a frame quilting method to create perfectly quilted squares. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread colours:
  Colour matched to suit the main background colour of your fabric.

Tuft Square

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  Tufts are spaced every 15cm horizontally and 15cm vertically.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Durable medium to heavy weight fabrics preferred. Heavily embroidered fabrics not recommended for tuft quilting. Velvets not suitable.

• Process Used:
  BQ use a frame quilting method to create even tuft spacing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Tuft Diamond

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads. Maximum quilting area is 304cm wide x 279cm length. Some king size bedspreads may need to be outline or multi-needle channel quilted, due to restrictions on the sewing frame size.

• Quilting dimensions:
  Tufts are spaced every 30cm horizontally and 30cm vertically. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Durable medium to heavy weight fabrics preferred. Heavily embroidered fabrics not recommended for tuft quilting. Velvets not suitable.

• Process Used:
  BQ use a quilting frame to create even tuft spacing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Border with Straight Diamond

Ideal for: Cap top style bedspreads only with square corners and without a sham. Can only be used on standard size bedspreads.

• Quilting dimensions:
  30cm x 30cm. Quilting dimensions are approximates and vary depending on filling weight used.

• Suitable Fabrics:
  Plain and patterned fabrics. For large products such as bedspreads, quilt covers and some bedhead styles, wide width fabrics are recommended to avoid visible fabric joins. Where fabric joins are required, pattern fabrics will be pattern matched and plain fabrics or fabrics with minimal pattern will have exposed fabric joins. Durable medium to heavy weight fabrics preferred. Velvets not suitable.

• Process Used:
  BQ use a quilting frame to create even tuft spacing. First we cut and join the fabric and then we quilt, providing perfect pattern and quilting match.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Outline Channel

A straight line of stitching traces along the check or stripe pattern of the fabric, emphasising the fabric pattern and providing greater stitching accuracy as compared to other quilting methods. Channel width is dependent on the fabric design.

• Quilting Process Used:
  We cut and join the fabric first and then we quilt, providing pattern and quilting match. Outline quilting is completed by hand by our experienced machinists.
  Recommended for king size bedspreads that may be too large for frame quilting.

• Suitable Fabrics:
  Pattern fabrics with a straight horizontal or linear pattern, and where quilting lines need to exactly follow the fabric pattern to form a quilted channel look. Durable medium to heavy weight fabrics preferred. Velvets not suitable.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Outline Pattern

Emphasises the pattern on your floral, plaid or check fabric.
Our machinest traces a line of stitching around the fabric pattern. Recommended for patterns not too busy and not too spread out across fabric.

Ideal for: Bedspreads, quilt covers, throw rugs, bed valances, pillowcases, cushions, wall panels and bedheads.

• Suitable Fabrics:
  Durable medium to heavy weight fabrics preferred. Velvets not suitable.

• Process Used:
  First we cut and join the fabric and then our machinest sews your unique quilting pattern suited to your fabric.

• Thread Colours:
  Colour matched to suit the main background colour of your fabric.

Ordering Tips

Semicircle (BH14)

Semicircle shaped bedhead with plain front and no side seams.

Bedhead shapes available: 10 only.

Suitable Fabrics:

Sizing:
Select a standard size detailed below or request a customised size. Non standard sizes not available.

Single: 110cm W x 120cm H
King Single: 127cm W x 129cm H
Double: 158cm W x 144cm H
Queen: 173cm W x 152cm H
King: 203cm W x 167cm H

Finished bedhead projection (in centre of bedhead) is 7cm.

Mounting:
The following options are available for securing your bedhead:

• Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
• All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

The Semicircle style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

5 Panel (BH15)

Five separate panels with plain fronts and no side seams.

Bedhead shapes available: 9 only.

Suitable Fabrics:
Best for plain fabrics, vinyls, leathers and suede.
We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.

Sizing:
Select a standard size detailed below or request a customised size. Single, king single and double size bedheads not available. Maximum height 170cm.

Queen: 270 cm W x 120cm H
King: 320 cm W x 120cm H

Finished bedhead projection (from centre of bedhead) is 5.5cm.

Mounting:
The following options are available for securing your bedhead:

• Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall. Plates to join the panels and small metal legs are available on request to be fastened onsite.
• Each panel is supplied with a wall mounting bracket to enable bedhead attachment to the wall, providing greater stability. Walls must be strong enough to hold approx 50kg of bedhead.

The 5 Panel bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

Duo (BH12)

Two separate panels with plain fronts and 50mm seamed walled sides.

Bedhead shapes available: 8 (slightly rounded corners) is standard. Shape 9 (square corners) available on request.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest.
  View our quilting styles.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection (at centre of bedhead) is 9cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall. Plates to join the panels and small metal legs are available on request to be fastened onsite.
  • Both panels are supplied with a wall mounting bracket to enable bedhead attachment to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The Duo style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is requested.

Folded Corner (BH11)

A plain style front with 5cm walled side. Fabric is folded into pleat in top corners. No side seams and piping present.

Bedhead shapes available: 8 and 9.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest. View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 8cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The Folded Corner style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

Flanged (BH10)

A flanged slip cover is pulled tightly over an upholstered bedhead frame. A 1cm flange sits on top and side edges. Flange size can vary on request.

Skirting board and base cut-out not available.

Bedhead shapes available: 9 only.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics. We can also quilt your fabric prior to upholstering for added interest. The bedhead flange will also be quilted.
  View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single sized flanged bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead. The wall mounting bracket (2cm projection) is attached to the slip cover, hence cover can not be removed. Wall mounting bracket can be omitted on request.

  The Flanged style bedhead sits up to 2cm away from wall if wall mounted above skirting boards or bedhead sits on floor between bed and wall. Skirting board cutout is unavailable.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 4cm (excludes wall mounting bracket).

Winged (BH9)

A plain style front with surrounding wings, available in five different wing shapes.

Bedhead shapes available: 2, 3, 5, 6, 7 and 9.

Surrounding wing shapes available: A – E.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest. View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Wing projection is 30cm at widest section of wing.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The Winged style bedhead sits on the floor and is not recommended for mounting above skirting boards. To sit flushed to the wall, skirting board cutouts are required on request.

Rectangle Panel (BH8)

This bedhead style consists of horizontal and vertical seams sewn into fabric to create rectangle panels along with blind button detail.

Additional rows of panels are available on request, for non standard height bedheads.

Bedhead shapes available: 8 and 9.

• Suitable Fabrics:
  Best for plain fabrics, vinyls, leathers and suede.
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The Rectangle Panel style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	120cm W x 120cm H
  King Single:	120cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 8cm.

Deep Diamond Button (BH7)

Upholstered with covered deeply inset buttons in a diamond configuration. Optional surrounding wings in shapes A-E can be added. Studs or sewn wall can be added to wing.

Bedhead shapes available: 1, 4, 8 and 9.

Base cut-out not available.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  Fabric must be railroaded.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede.
  Contrast fabrics can also be used on bedhead buttons.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall. Recommended if wings added.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The Deep Diamond Button style bedhead sits flushed to the wall if mounted above skirting boards or bedhead sits on floor and a skirting board cut-out is included. If optional wings added, skirting board cut-out also added to wings. Base cut-out unavailable.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	120cm W x 120cm H
  King Single:	120cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 10.5cm.

Vertical Panel (BH6)

Consists of vertical deep panels approx. 20cm each in width. Panels can be made wider on request.

Bedhead shapes available: 8 and 9.

Base cut-out not available.

• Suitable Fabrics:
  Best for plain fabrics, vinyls, leathers and suede.
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The Vertical Panel style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 10.5cm.

Walled (BH5)

Plain style front with 5cm seamed walled side and 4.5mm piping on front and back wall edge. Piping can be omitted on request.

Bedhead shapes available: 1 to 8, and 9 if no piping required.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest. View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on piping and side wall.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 9cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The Walled style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

Plain (BH4)

A plain style front with no side seams and single row of 7mm piping on back wall edge. Piping can be omitted on request.

Bedhead shapes available: 1 to 8, and 9 if no piping required.

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest.View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on piping.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 6cm. Add a further 2cm to projection if a wall mounting bracket is attached.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The plain style bedhead sits 2cm away from wall if mounted above skirting boards or sits on floor. Skirting board cut-out is unavailable.

Padded Roll (BH3)

Consists of a padded roll with 7mm piping inserted below roll. Roll width is 9cm for single bed and 12.5cm all other bed sizes. 60cm high main insert sits deeper than surrounding roll. Calico insert sits behind mattress (can be omitted on request, additional main fabric may be required).

Bedhead shapes available: 1 to 8

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. For added interest, we can also quilt fabric for the main insert, prior to upholstering. View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on bedhead roll, insert and piping.
  Please note: calico fabric is upholstered behind mattress with this bedhead style. If you require calico to be omitted, please mention on BQ Order Form and supply sufficient fabric as quoted by BQ.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 6cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall. There will be a gap between the bedhead and wall depending on width of skirting board.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The padded roll style bedhead sits up to 2cm away from wall if mounted above skirting boards or sits on floor. Skirting board cutout is unavailable.

Padded roll with piping above

Bedspread hem is 8cm padded roll in quilted self fabric, with self or contrast fabric piping above roll.
This is a suitable hem style for floor length bedspreads with rounded corners only.

Padded Band (BH2)

Consists of a 15cm wide padded band with 7mm piping inserted below band and 60cm high main insert. 5cm seamed walled side. Calico insert sits behind mattress.

Bedhead shapes available: 8 and 9

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. For added interest, we can also quilt fabric for the main insert, prior to upholstering.View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on bedhead band, insert, piping and side wall.
  Please note: calico fabric is upholstered behind mattress with this bedhead style. If you require calico to be omitted, please mention on BQ Order Form and supply sufficient fabric as quoted by BQ.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width 210cm and maximum height 170cm.

  Single:	110cm W x 120cm H
  King Single:	127cm W x 120cm H
  Double:	158cm W x 120cm H
  Queen:	173cm W x 120cm H
  King:	203cm W x 120cm H

Finished bedhead projection is 7cm.

• Mounting:
  The following options are available for securing your bedhead:
  • Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
  • All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

  The Padded Band style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is included.

Square Panel Insert (BH13)

This bedhead style consists of a 15cm wide padded band and square panel sewn insert with blind button detail.

Additional rows of panels are available on request, for non standard height bedheads.

A calico insert sits behind mattress.

Bedhead shapes available: 8 and 9.

Sizing:
Select a standard size detailed below or request a customised size. Single size bedhead not available. Maximum width 210cm and maximum height 170cm.

King single : 127cm W x 120cm H
Double: 158cm W X 120cm H
Queen: 173cm W X 120cm H
King: 203cm W X 120cm H

Finished bedhead projection (from centre of bedhead) is 8cm.

Mounting:
The following options are available for securing your bedhead:

• Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
• All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.

The Square Panel Insert style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is requested.

Suitable Fabrics:
Best for plain fabrics, vinyls, leathers and suede.
We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.

Shape 8

Shape 9

Shape 10

Shape 6

Shape 7

Shape 5

Shape 4

Shape 3

Shape 2

Shape 1

Stained battens

Add 9 mm thick wooden stained or painted battens in a range of available colours, to your roman style panelsfor further customisation.

Stained batten colour options:

• dark oak
• light oak
• golden oak
• natural
• linen
• lemon

Painted batten colour options:

• BQ white
• BQ cream
• or provide your own paint

Ordering Tips

Ordering Tips

• Vertical channel quilted (BV4):
  This bed valance style is quilted with 10cm wide vertical channels as standard and 100g polyester filling. Other quilting styles and fillings are available on request. Please specify your requirements on the OPTIONAL FEATURES page.

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Evo

Evo curtains offers a similar look to Inverted Pleat curtains, although they are made with a single pleat at the back which enables the curtain to stack back efficiently to maximise the window vantage.

Evo curtains runs on a glide system and require an Evo rod. BQ supply two styles of glides suitable for Evo rods or supply your own glides.

BQ uses 90mm wide clear buckram for an Evo curtain heading.

• Suitable Fabrics:
  Solid fabrics.

• Lining:
  Select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Evo curtains can also be made unlined when using a solid fabric.

• Seams:
  Vertical fabric join seams will be hidden on curtain heading.

• BQ standard fullness:
  x2.5 for solid fabrics. Other fullness options available on request. Evo curtains require more fabric to Inverted Pleat curtains.

• Maximum Drop:
  600cm

Ordering Tips

Inverted Pleat

Inverted Pleat curtains are also known as a reverse pleat or box pleat and offers a contemporary look. This curtain style does not stack back as comprehensively as other styles. Evo curtains offer a similar heading style with a more condensed stack back.

BQ uses 100mm wide buckram for the curtain heading.

• Suitable Fabrics:
  Solid and sheer fabric types, although heading buckram will be obvious on very sheer unlined fabrics. For fabrics with vertical stripes, consider the interuption to pattern flow along the curtain heading due to pleats. For fabrics with vertical stripes, consider the interruption to pattern flow along the curtain heading due to inverted pleats.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• Seams:
  Vertical fabric join seams will be hidden on curtain heading.

• Hooks:
  When ordering, specify your preferred two prong hook size depending on the type of rod or track to be used and the curtain position required. Visit Customer Login for further hook info.

• BQ standard fullness:
  x1.8 for solid and sheer fabrics. Other fullness options available on request.

• Maximum Drop:
  600cm

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Ordering Tips

Scandi

An unstructured minimalist heading style with soft loose folds.

Similar to a Flat Panel curtain but made with a discreet 100mm wide heading without the stiff buckram heading tape.

• Suitable Fabrics:
  Solid and sheer fabrics with a soft handle for the best result in hanging. Contact BQ to confirm fabric suitability. This heading style is not suitable for very fine or thin sheers, very open weave sheers or heavy stretchy fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• Maximum Drop:
  600cm

• Hooks:
  Scandi curtains are supplied with pin hooks placed 5mm from curtain top edge and 100mm apart as standard, or request alternate positioning to suit type of rod or track used.

• BQ standard fullness:
  x1.8 for solid and sheer fabrics. Other fullness options available on request. Request less fullness for a curtain with minimal folds or for a curtain with fuller looser folds and more body and fabric request greater fullness and consider wider hook spacing.

Relaxed Fold

A relaxed and modern heading style with gentle irregular folds.  The curtain is made with a flat finish heading with no pleating or gathering.

BQ uses a soft 75mm wide white heading tape, with clear tape available on request.

• Suitable Fabrics:
  Solid and sheer fabrics with a soft handle for the best result in hanging.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested.

• BQ standard fullness:
  x2 for solid and sheer fabrics. Other fullness options available. Request less fullness for a curtain with minimal folds or for a curtain with fuller looser folds and more body and fabric greater fullness.

• Maximum Drop:
  600cm

Flat Panel

Flat Panel curtains offer a simple and versatile curtain style. The curtain is made with a flat finish heading with no pleating or gathering. When the curtain is hung on a rod or track, curtains with a standard 1.5 fullness will sit in gentle waves. For an almost flat curtain with minimal or no wave when closed, request a low curtain fullness or for a curtain heading style with fuller loose waves request a higher curtain fullness.

Flat panel curtains are often used with a decorative rod with or without rings.

BQ uses a 100mm wide buckram for the curtain heading, creating a stiffer heading style than Scandi curtains.

• Suitable Fabrics:
  Solid and sheer light to medium weight fabrics including linens, cottons and silks. Heading buckram will be obvious on very sheer unlined fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested.

• BQ standard fullness:
  x1.5 for solid fabrics. Other fullness options available on request.

• Maximum Drop:
  600cm

Ripplefold (S-fold)

Ripplefold curtains are a contemporary and popular curtain style with neat and simple uniform folds. The curtains are made with a 30mm wide press stud heading tape provided by our customer.

They are installed with a ripplefold track or rod installed above the window or on the ceiling.

• Suitable Fabrics:
  Solid and sheer fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• Maximum Drop:
  600cm

• BQ standard fullness:
  x2.2 for solid and sheer fabrics. Other fullness options available on request.

Ordering Tips

Headrail system

Bonded Roller Blind – Ordering Tips

FABRIC

QUANTITY & SIZING

This bedhead style consists of a 15cm wide padded band and square panel sewn insert with blind button detail.

Additional rows of panels are available on request, for non standard height bedheads.

A calico insert sits behind mattress.

Bedhead shapes available: 8 and 9.

Chain Side: Chain not required for blinds with a motorisation system or spring assist.

Fabric: Please provide the following fabric information to BQ if applicable (and upload images to assist) :

* Face side of fabric and pattern direction, if confusion may occur
* Contrast fabric/trim exact placement and sizing

* if using the fabric(s) mentioned with another BQ order.

Fabric pattern match : Please notify BQ if you have fabric pattern match requirement. Additional fabric may be required. If multiple blinds are installed in the same room, BQ will pattern match print fabric from base of blind as standard and the pattern will be centred and horizontally aligned on each blind.

Fabric pattern flow : Please notify BQ if you have fabric pattern flow requirement where print fabric is used on adjoining/butting blinds. Additional fabric may be required.

How Measure Width:

• Pin to Pin : The finished width of blind from bracket to bracket, including roller. For face fix blinds provide your architrave to architrave width.For blinds installed in recess, provide recess width and select Recessed – YES and we will make adjustments for perfect blind fit in recess.
• Cloth to Cloth : The finished width of the blind fabric only.
  

Mounting:
The following options are available for securing your bedhead:

• Bedhead can sit on the floor between the bed and wall with no attachment to bed or wall.
• All BQ bedheads are supplied with a wall mounting bracket to enable the bedhead to be attached to the wall, providing greater stability. Walls must be strong enough to hold 15-50kg of bedhead.
• Adjustable bedhead legs can be supplied by BQ, at an additional cost, providing stability and avoiding the need to secure bedhead to the wall. Consider adding a base cut out (no charge) if bedhead is to sit on the floor.

The Square Panel Insert style bedhead sits flushed to the wall if wall mounted above skirting boards or bedhead sits on floor and a skirting board cutout is requested.

Railroaded Fabric : Railroaded fabric is suitable for wide width fabrics and standard width fabrics where blind drop is 1100mm or less.

Recessed: Please specify if blind will be installed in a window recess. BQ will make adjustments to  your measurements to ensure perfect fit.

Roll:

Normal roll: Fabric falls to back of roller (BQ standard).

Reverse roll: Fabric falls to front of roller, covering roller tube.

Window Name: Please provide location of window to assist with queries, package labeling and installation.

Eyelet

Eyelet curtains are made with individual metal eyelet rings punched through the fabric. Eyelet sizes come in a 60mm external diameter and 40mm internal diameter. The 40mm internal diameter best suits a 25mm curtain rod.

BQ supply a nickel plated (silver) steel eyelet as our standard or zinc, brass, antique brass or black eyelets can be used on request.

• Suitable Fabrics:
  Solid and sheer fabrics.

• Lining:
  If lining your curtains, select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Alternatively install a dual curtain track or rod with a separate curtain made from blockout lining fabric.

• BQ standard fullness:
  x2 for solid fabrics and x2.5 for sheer fabrics. Other fullness options available on request.

• Maximum Drop:
  600cm

Bonded Pelmet

An unpadded pelmet, available in a straight, shape 1 and 3 only.
Made with 4.5mm piping along top and base edge of pelmet, in self or contrast fabric. Piping can be omitted on request.
Fabric is bonded to a strong wood custom made pelmet frame.
Combine with curtains, roman blinds or roller blinds.

• Suitable fabrics:
  Most medium and heavy weight solid fabrics are suitable for pelmets, although linen and viscose blends may stretch over time. Light weight fabrics such as silks and sheers can be used but cotton interlining is recommended and can be supplied by BQ.
  Fabrics can be railroaded on request to avoid joins or consider wide width fabrics to minimise amount of fabric required. If using a patterned fabric, railroading may not be suitable. BQ will expertly pattern match at fabric joins.

• Sizing:
  Provide width, drop and return measurements for either inside box measurements (IBM) or outside box measurements (OBM). Cut-outs can be added to ensure pelmet fits perfectly. Maximum drop is 40cm and maximum size of returns is 20cm. For pelmets over 390cm customer must organise own freight or collection from BQ’s Melbourne workroom. Alternatively, pelmets can be made in two or three pieces. We recommend three pieces to avoid a centre join and interruption to any fabric pattern.

Goblet Pleat

Goblet pleat curtains provide a formal style. If you are furnishing a traditional or stately old home and have a sumptuous fabric a Goblet style heading could be a good option.

BQ use 100mm wide clear buckram for the curtain heading and each goblet is filled with wadding.

• Suitable Fabrics:
  Solid fabrics.

• Lining:
  Select from our range of blockout or translucent lining fabrics or supply your own. BQ’s standard lining is 3 pass blockout lining in ivory colour, attached to the curtain with plastic shanks unless otherwise requested. Goblet pleat curtains can also be made unlined when using a solid fabric.

• Seams:
  Vertical fabric join seams will be hidden on curtain.

• Hooks:
  When ordering, specify your preferred two prong hook size depending on the type of rod or track to be used and the curtain position required. Visit Customer Login for further hook info.

• BQ standard fullness:
  x2 for solid. Other fullness options available on request.

• Maximum Drop:
  600cm

Gather Pleat

Shaped base

Double fold at top

Double fold at top with contrast band

Dropped base

Piping

Add 4.5mm or 7mm piping if not already part of our standard bedhead style. Select like or contrast fabrics, added to bedhead sides where seams exist or back edge where bedhead sits along wall.

Suitable for bedhead styles: BH1, BH2, BH3 and BH13.

We can also add braid or decorative cord trim to replace piping on face of BH3 and BH4 bedhead styles.

Stuckey (BH1)

A plain short style with foam padding in 5.5cm or 10cm (BQ standard) projection. Sits neatly along the mattress, flushed to the wall. Does not go to floor.

Bedhead shapes available: 9 only

• Suitable Fabrics:
  We recommend a durable, stain resistant and easy to clean fabric suitable for upholstery use. Also consider the possibility of fabric fading if bedhead is positioned near a window.
  BQ can manufacture this bedhead style with plain or print fabrics, vinyls, leathers and suede. We can also quilt your fabric prior to upholstering for added interest. View our quilting styles.
  To avoid vertical fabric join seams BQ recommend wide width fabrics or railroading fabric (turning sideways), where fabric/pattern allows. Fabric railroading is not usually required for Single and King Single sized bedheads unless you prefer the look of railroaded fabric. Where fabric joins are present, BQ will always attempt to pattern match print fabrics to minimise exposure of joins.
  Contrast fabrics can also be used on covered buttons or piping on back wall edge, if requested.

• Sizing:
  Select a standard size detailed below or request a customised size. Maximum width is 210cm. This bedhead style is made 5cm wider than the standard mattress width.

  Single:	97cm W x 60cm H
  King Single:	112cm W x 60cm H
  Double:	143cm W x 60cm H
  Queen:	158cm W x 60cm H
  King:	188cm W x 60cm H

• Mounting:
  Bedhead needs to be attached to wall, using wall mounting bracket provided by BQ.

Quilted with bound edge (BT2)

The throw rug face side is quilted in a multi-needle channel, frame or outline style and finished with a bound edge, in same or contrast fabric on all sides.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Quilted with contrast band on four edges (BT8)

The throw rug face side is quilted in a channel, multi-needle or outline style and finished with a 10cm contrast band on all sides, visible on face side only.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Quilted with 4.5mm piped edge (BT3)

The throw rug face side is quilted in a multi-needle channel, frame or outline style and finished with a 4.5mm piped edge, in same or contrast fabric on all sides. 7mm piping also available on request.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Quilted with flange (BT6)

The throw rug face side is quilted in a multi-needle channel, frame or outline style and finished with a 7cm flange edge, in same or contrast fabric on ends only. Other flange sizes can be requested.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L

• Filing options:
  Filled with 70g weight polyester as BQ standard. Other filling options available on request include:

  100g or 150g polyester	for a puffier effect
  cosy cotton	100% cotton, flat look, a lightweight deluxe option
  bumph	100% cotton, flat look, slightly lighter weight than cosy cotton

Quilted with contrast band on ends (BT7)

The throw rug face side is quilted in a multi-needle channel, frame or outline style and finished with a 15cm contrast band on ends only, visible on face side. Other band sizes can be requested.

The reverse side of the throw rug can be same or contrast fabric and either:

• unquilted and bag lined (BQ standard) or
• same style quilted or
• BQ can supply cotton lining in ivory colour, on request.

View quilting styles available.

• Suitable Fabrics:
  Light to medium weight solid (non sheer) fabrics are preferred. Heavy commercial weight fabrics may be better for non quilted throw rugs and fabrics with heavy embroidery are better outline or channel quilted rather than frame quilted.Visit Customer Login for further fabric suitability info or contact BQ.

• Sizing:
  Select a standard size detailed below or request a customised size.

  Single:	152cm W x 65cm L
  Double:	198cm W x 65cm L
  Queen:	213cm W x 65cm L
  King:	243cm W x 65cm L